B Series

BER Series

U Series

SF Series

Submersible aerator

TRN Series

- Semi-open, single vane impellers (1 hp - 5 hp models)

- Enclosed multi-vane impellers (7.5 hp - 300 hp models)

- Field adjustable/replaceable wear plates

- Highly efficient air filled motors for continuous duty operation

- Available with class E, B, F insulation to minimize operation costs. Double inside mechanical seals with Sic-Sic faces operate in a separate oil-filled chamber.

- Anti-wicking block prevents water incursion to the stator if cable is accidentally damaged

- Double-shielded, permanently lubricated high-temp C3 ball bearings rated for B-10 life of 60,000 hours

- Water jacket ensures perfect water cooling by circulating drainage around the motor housing (available on 30 hp or above)

- Municipal water supply stations and sewage treatment plants for pumping water,

- Sewage, and digested sludge.

Free Standing
- Silencer & Valve Set
- Lifting Chain 5m, (with Shackles)
- Suction Casing (with Nozzle Ring, Packing & Bolts)
- Screwed Flange
- Diffuser (with Packing & Bolts)
- Diffuser Base (with Nuts)

Guide Rail Fitting - TOS

- Silencer & Valve Set
- Lifting Chain 5m, (with Shackles)
- Guide Support (with Bolts & Nuts)
- Air-inlet Pipe Support (with U-bolt & Nuts)
- Guide Hook (with Bolts)

- Nozzle (with Nozzle Ring, Packing & Bolts)
- Suction Casing
- Guide Connector (with Bolts)
- Screwed Flange
- Diffuser (with Packing & Bolts)
- Foundation Bolts (with Nuts)

- Pre-aeration and mixing at wastewater
treatment plant
- Supplying oxygen to water in aquafarm

Free Standing
- Discharge Bend (with Packing & Bolts)
- Screwed Flange
- 1.5kW and below
- JIS 10kg/cm2 Flange (with Packing, Bolts & Nuts)
- 2.2kW and above

Guide Rail Fitting - TOS

- Lifting Chain 5m, (with Shackles)
- Guide Support (with Bolts & Nuts)
- Guide Hook (with Bolts)
- Duckfoot Bend
- Guide Connector (with Bolts)
- JIS 10kg/cm2 Flange (with Packing, Bolts & Nuts)
- Foundation Bolts (with Nuts)

- Transferring sewage and wastewater to wastewater treatment plant
- Draining wastewater from industrial plant
- Draining effluent from residence, hotel, commercial complex, etc

Free Standing
- Discharge Bend (with Packing & Bolts)
- Screwed Flange
- 1.5kW and below
- JIS 10kg/cm2 Flange (with Packing, Bolts & Nuts)
- 2.2kW and above

Guide Rail Fitting - TOS

- Lifting Chain 5m, (with Shackles)
- Guide Support (with Bolts & Nuts)
- Guide Hook (with Bolts)
- Duckfoot Bend
- Guide Connector (with Bolts)
- JIS 10kg/cm2 Flange (with Packing, Bolts & Nuts)
- Foundation Bolts (with Nuts)

- Drainage treated water at wastewater treatment plant

- Pumping rainwater and springwater from underground

- Supplying treated water for deforming at wastewater treatment plant

• - The open rotor of the TRN series suctions a large volume of water for the motor power through the pump basket.

  - This water is then mixed with air and distributed horizontally in all directions through the channels of the guide ring.

  - The top of the rotor is hollow and allows the air that has been suctioned in to fill the area around the shaft seal so that it can mix with the water at the rotor.

  - One consequence of this is that alayer of air is formed separating the shaft seal from the medium and thereby substantially increasing the life of the shaft seal.

- Another effect is that the water that is suctioned in isoxygenated with tiny air bubbles, effectively aerating the waste water.

- Pre-aeration and primary aeration at industrial wastewater treatment facilities.